Display section

Type

5.8-inch low-temperature polysilicon LCD (800 x 480 dots)
10 div x 8 div (60 dots/div, when grid is selected)

CRT

Type

2-inch dia., CCD scan converter tube (380,000 pixels)

Persistence characteristics

Fastest writing speed

10 div/ns

Persistence time

Variable between 0 and infinity

Waveform recording

Screen waveforms can be recorded/deleted by key manipulation

Single storage

Auto INTEN adjustment function linking time and div

Vertical deflection system (Y axis)

Mode

CH1, CH2, CH3, CH4, ADD (CH1±CH2), ALT/CHOP (555kHz±1%)

CH1,2

Sensitivity range

50 Ohm

5mV/div - 1V/div 8 steps (1-2-5)

1M Ohm

5mV/div - 5V/div 10 steps (1-2-5)

Variable

Adjustable to less than 1/2.5

Accuracy

±2%

Frequency bandwidth (-3dB)

50 Ohm

TS-81000: DC - 1GHz (10mV - 1V/div)

TS-80600: DC - 600MHz (10mV - 1V/div)

DC - 500MHz (5mV - 9.9mV/div)

1M Ohm
(Passive probe model SS-101R is optional)

DC - 500MHz (10mV - 5V/div) at tip of SS-101R probe

DC - 350MHz (5mV - 9.9mV/div) at tip of SS-101R probe

Rise time

(50 Ohm 10mV - 1V/div)
Calculated from freq. Bandwidth x rise time = 0.35

Offset voltage

5mV - 50mV/div: ±1V
100mV - 500mV/div: ±10V
1V - 5V/div: ±100V

Offset accuracy

±(1.5%+0.5% of full scale + 1mV)

Input RC

50 Ohm: ±2%
1M Ohm: ±1% // 16pF
(DC 1M Ohm 5mV - 5V/div, AC 1M Ohm 100mV - 5V/div)

1.2M Ohm ± 1.0% // 16pF (AC 1M Ohm 5mV - 50mV/div)

Input coupling

DC 50 Ohm, DC 1M Ohm, AC 1M Ohm, GND

Max. input voltage

50 Ohm: 5Vrms
1M Ohm: 250Vmax (DC+peakAC, <= 5kHz)

CH3,4

Sensitivity range

100mV/div, 500mV/div

Sensitivity accuracy

±2%

Frequency bandwidth (-3dB)

DC - 500MHz

Offset voltage

100mV/div: +/-1V
500mV/div: +/-5V

Input RC

1M Ohm: +/-1.0% // 16pF

Input coupling

DC 1M Ohm, AC 1M Ohm

Max. input voltage

1M Ohm: 250Vmax (DC+peakAC, <= 5kHz)

ADD

Frequency bandwidth (-3dB)

Lower cutoff for AC couple

10Hz (-3dB)

Bandwidth limiter

20MHz
200MHz

Probe sense

10:1, 100:1 detection

Channel time difference

Skew adjustment function available

Signal delay time

20ns

Trace separation

More than 4div

Triggering

A triggering

Frequency

Signal sources

CH1, CH2, CH3, CH4, LINE

Coupling

DC: DC - fmax
AC: 100Hz - fmax
HF-REJ: Attenuated at 10kHz or more
LF-REJ: Attenuated at 10kHz or less

Slope

+,-

Sensitivity

50 Ohm 5mV/div - 9.9mV/div fmax: 500MHz
50 Ohm 10mV/div - 1V/div fmax: 1GHz (TS-81000)
50 Ohm 10mV/div - 1V/div fmax: 600MHz (TS-80600)

B triggering

Frequency

DC - 500MHz

Signal sources

CH1, CH2, CH3, CH4

Coupling

DC: DC - 500MHz
AC: 100Hz - 500MHz
HF-REJ: Attenuated at 10kHz or more
LF-REJ: Attenuated at 10kHz or less

Slope

+,-

Sensitivity

TV triggering

NTSC, PAL, CUSTOM
Line select (1 to 3000), Field select (1,2,4,8)
CUSTOM (including HDTV)

Polarity

+,-

Sensitivity

1.5 - 8.0div
TV clamp available

Event trigger

Count mode

Range:1 - 65535
Max. count frequency: 50MHz

Burst mode

Range: 0.15 microseconds - 9.99 seconds

Trigger level variable range

±8.0div

Horizontal deflection system (Y axis)

Horizontal display

A, ALT, B, X-Y

A sweep

Sweep mode

AUTO, NORMAL, SINGLE

Max. sweep rate

200ps/div(TS-81000)
500ps/div(TS-80600)

Range

2ns - 200ms/div 25 steps, 1-2-5 (TS-81000)
5ns - 200ms/div 24 steps, 1-2-5 (TS-80600)

Variable

2ns - 600ms/div (TS-81000)
5ns - 600ms/div (TS-80600)

Accuracy I (*1)

±2% (5ns - 200ms/div) over center 8div
±3% (2ns/div) over center 8div (TS-81000)

Accuracy II (*1)

±5%(5ns - 200ms/div) any 2div within center 8div
±6% (2ns/div) over center 8div
(*1) 20ns or 1div for the beginning of the sweep and 20ns for the end of sweep should be excluded.
Add 1% when VARIABLE is ON

B sweep

Delay method

Triggered delay (TRIG'D DELAY)
Continuous delay (RUNS AFTER DELAY)

Max. sweep rate

200ps/div (TS-81000)
500ps/div(TS-80600)

Range

2ns - 20ms/div 22 steps, 1-2-5 (TS-81000)
5ns - 20ms/div 21 steps, 1-2-5 (TS-80600)

Accuracy I (*2)

±2% (5ns - 200ms/div) over center 8div
±3% (2ns/div) over center 8div

Accuracy II (*2)

±5% (5ns - 200ms/div) any 2div within center 8div
±6% (2ns/div) over center 8div (TS-81000)
(*2) 20ns or 1div for the beginning of the sweep and 20ns for the end of sweep should be excluded

Dual delay

Available

Delay jitter

Less than 1/50000

Sweep magnification

x 10

Hold off time

Variable 1sec. max.

X-Y

X axis

CH1

Sensitivity

Same as CH1

Frequency bandwidth

10MHz (-3dB)

Y axis

CH1, CH2, CH3, CH4

Sensitivity

Same as each CH

Frequency bandwidth

Same as each CH

X-Y phase difference

Within 3° (DC - 5MHz)

CAL signal

Waveform

Square-wave

Frequency

1kHz ± 0.1%

Output voltage

0.6V ± 1%

CH2 OUT

Amplitude

20mV/div ± 20% (50 Ohm)

Frequency bandwidth

500MHz(-3dB) 50 Ohm, 10mV/div - (TS-81000)
300MHz(-3dB) 50 Ohm, 10mV/div - (TS-80600)

Output resistance

50 Ohm ± 10%

Z AXIS IN

Intensity modulation voltage

0.5Vp-p

Polarity

Dark with positive voltage and brighter with negative voltage

Frequency range

DC - 5MHz

Input resistance

5k Ohm ± 20%

Input voltage

± 40V max.

Probe power supply

Connectors

2

Suitable probes

SFP-4A, SFP-5A, SS-250, SS-240A, SS-240

Auto Setup

Auto Setup

Input sensitivity, Offset, TIME/DIV, Trigger level
Amplitude: 30mV - 35V
Frequency: 50Hz-200MHz

Cursor measurement

Delta t

Relative time difference measurement with cursor
Resolution: 1/60div

Delta V

Relative voltage difference measurement with cursor
Resolution: 1/60div

Frequency counter

Frequency bandwidth

2Hz - 1GHz (TS-81000)
2Hz - 600MHz (TS-80600)

Digit

6 digits, accuracy ± 0.01%

Clock

Display

Month/Date/Time/Minute

Accuracy

<=±50ppm

Interface

Remote control

10Base-T Ethernet

PC card slot

ATA card available (PCMCIA Type II)

External Monitor out

VGA WIDE

NTSC output
(Composite, S out)

Amplitude: 1Vp-p ± 0.3V 75 Ohm
Output resistance: Approx. 75 Ohm (AC coupling)

Built-in printer

Line thermal printer
Printing speed: 10mm/sec
Paper size: Width 112mm, length 25m

Power supply

Voltage range

100V - 240V AC 50/60Hz

Power consumption

200VA max. (with built-in printer operation)

Power consumption in the Standby mode

5VA max.

Insulation resistance

DC 500V, 100M Ohm or higher

Insulation withstanding voltage

DC 2kV, 2 seconds, 5mA or lower

Weight and dimensions

Dimensions

Approx. 198H x 332W x 406Lmm (accessories and projections are not included)

Weight

Approx. 10kg (accessories and options are not included)

Environmental conditions

Operating range Temperature

0 - +40°C
+5 - +40°C (Built-in printer operation temperature)

Humidity

<= 90% 40°C

Performance guaranteed temperature

+10 - +35°C

Preheating time

These specifications are guaranteed after power has been on for 30 minutes or longer.

Storage range Temperature

-20 - +60°C 80% RH

Operating

2,000m, air pressure of approx. 79kPa

Not operating

15,000m, air pressure of approx. 12kPa

Accessories

Instruction manual (1), Power cord (1), Thermal printer paper (1)